Chocolate Meltaways: A Fabulous Fudge Recipe (2024)

FAQs

What is the secret to good fudge? ›

By cooling the fudge prior to agitation (like in the recipes included in this article), on the other hand, you'll get much smaller, finer sugar crystals and a finished fudge with a smooth, creamy texture. Cool the mixture until it reads 120° F on the thermometer—no stirring. This can take 1 to 1/2 hours.

Options for what you can do with your unset fudge:

OPTION 1) Depending on how runny it is, you can either use it as a frosting for cakes, or a sauce for ice-cream. OPTION 2) Freeze it overnight. Cut it into squares. Cover each square thickly in melted chocolate, ensuring no part of the fudge is exposed.

If your fudge turned out super sticky, or it didn't set as it cooled, it probably never got hot enough. This mistake is super easy to avoid if you use a candy thermometer and cook the fudge to the temperature specified in the recipe (usually between 234 and 239°F).

Evaporated milk doesn't have sugar added. The sweetened condended milk is needed as no extra sugar is added to the fudge. If evaporated milk were used then the fudge would not be sweet enough and also would still be too soft unless the fudge is frozen.

Avoid Stirring Once the Mixture Comes to a Simmer

Another key part of a successful fudge texture is when you stir the mixture. Stirring the sugar and milk during the initial stages of cooking allows the sugar to dissolve. However, once the mixture comes to a boil, it's time to put the spoon down.

The fudge is then beaten as this makes the fudge slightly crumbly rather than chewy. Beating the mixture encourages the formation of small sugar crystals, which leads to the crumbly texture. The crystals may not be noticeable in themselves but the fudge mixture will thicken and turn from shiny to matte in appearance.

Fudge usually behaves this way when it's not cooked to a high enough temperature (due to oversight or a faulty candy thermometer). If your fudge is tough, hard, or grainy, then you may have made one of several mistakes: You may have overcooked it, beaten it too long, or neglected to cool it to the proper temperature.

Pop the grainy fudge back into the pan along with some water and a little cream and melt the fudge back down to a liquid and re-boil it to temperature. Heat slowly to begin with and make sure the mixture goes completely smooth before bringing it to the boil.

The main reason is that your Fudge has not reached the optimum temperature. If your mixture only reaches 110 or 112 degrees Celsius it will always be soft. That's why we recommend investing in a sugar thermometer. Another reason your Fudge is not setting is that the ratio of liquid to sugar is too high.

Should I cool fudge in the fridge? ›

NEVER REFRIGERATE your fudge as this will draw out the moisture and leave you with dry, crumbly fudge.

Why won't my 3 ingredient fudge set? This often happens when the condensed milk and chocolate chip mixture isn't hot enough to start. Everything must be completely melted before it is transferred to the pan to cool.

The key to successful, nongrainy fudge is in the cooling, not the cooking. The recipe calls for heating the ingredients to the soft-ball stage, or 234° F, then allowing it to cool undisturbed to approximately 110° F.

Cream of tartar is used in caramel sauces and fudge to help prevent the sugar from crystallizing while cooking. It also prevents cooling sugars from forming brittle crystals, this is why it's the secret ingredient in snickerdoodles!

The ingredients for fudge are combined and cooked to 234 degrees, cooled to 110 degrees without stirring, then beaten until creamy. Candy that isn't cooked long enough will end up too soft; overcooking makes fudge crumbly or hard.

Secondly, the pot's material should allow for good heat distribution hence your top choice should be copper cookware or a pot with a copper core. Copper's exceptional heat conductivity offers unparalleled temperature control, an asset when working with finicky ingredients like sugar.